CCNA3 v6.0 Chapter 4 Exam Full 100%
-
1. Question
Refer to the exhibit. Which switching technology would allow each access layer switch link to be aggregated to provide more bandwidth between each Layer 2 switch and the Layer 3 switch?
CCNA3 v6.0 Chapter 4 Exam 007
-
2. Question
Which statement is true regarding the use of PAgP to create EtherChannels?
-
3. Question
Which two protocols are used to implement EtherChannel? (Choose two.)
-
4. Question
Which statement describes a characteristic of EtherChannel? -
5. Question
Which statement describes an EtherChannel implementation? -
6. Question
An EtherChannel link using LACP was formed between two switches, S1 and S2. While verifying the configuration, which mode combination could be utilized on both switches? -
7. Question
What is an advantage of using LACP? -
8. Question
What is a best practice to use before beginning an EtherChannel implementation? -
9. Question
Which PAgP mode combination will establish an EtherChannel?
-
10. Question
Which three options must match in order to establish an EtherChannel between two directly connected switches? (Choose three.) -
11. Question
A network administrator is configuring an EtherChannel link between switches SW1 and SW2 by using the command SW1(config-if-range)# channel-group 1 mode passive. Which command must be used on SW2 to enable this EtherChannel? -
12. Question
Refer to the exhibit. An EtherChannel was configured between switches S1 and S2, but the interfaces do not form an EtherChannel. What is the problem?
CCNA3 v6.0 Chapter 4 Exam 008
-
13. Question
Refer to the exhibit. A network administrator has decided that an EtherChannel between ports 0/1 and 0/2 on switches S1 and S2 would help performance. After making the configuration, the administrator notices no performance gain. Based on the output that is shown, what two possible assumptions could a network administrator make? (Choose two.)
CCNA3 v6.0 Chapter 4 Exam 006
-
14. Question
Refer to the exhibit. A network administrator issued the show etherchannel summary command on the switch S1. What conclusion can be drawn?
CCNA3 v6.0 Chapter 4 Exam 005
-
15. Question
Refer to the exhibit. Based on the command output shown, what is the status of the EtherChannel?
CCNA3 v6.0 Chapter 4 Exam 002
-
16. Question
What is a requirement to configure a trunking EtherChannel between two switches? -
17. Question
What is the purpose of HSRP? -
18. Question
Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs? -
19. Question
Refer to the exhibit. A network administrator configured routers R1 and R2 as part of HSRP group 1. After the routers have been reloaded, a user on Host1 complained of lack of connectivity to the Internet The network administrator issued the show standby brief command on both routers to verify the HSRP operations. In addition, the administrator observed the ARP table on Host1. Which entry should be seen in the ARP table on Host1 in order to gain connectivity to the Internet?
CCNA3 v6.0 Chapter 4 Exam 004
-
20. Question
Refer to the exhibit. What statement is true about the output of the show standby command?
CCNA3 v6.0 Chapter 4 Exam 003
-
21. Question
Refer to the exhibit. A network engineer is troubleshooting host connectivity on a LAN that uses a first hop redundancy protocol. Which IPv4 gateway address should be configured on the host?
CCNA3 v6.0 Chapter 4 Exam 001
-
22. Question
A network administrator would like to ensure that router R1 is always elected the active router for an HSRP group. Which set of commands would ensure the required results?- R1(config-if)# ip address 192.168.1.100 255.255.255.0
R1(config-if)# standby 1 ip 192.168.1.1
R1(config-if)# standby 1 priority 1
R1(config-if)# no shutdown - R1(config-if)# ip address 192.168.1.250 255.255.255.0
R1(config-if)# standby 1 ip 192.168.1.1
R1(config-if)# no shutdown - R1(config-if)# ip address 192.168.1.100 255.255.255.0
R1(config-if)# standby 1 ip 192.168.1.1
R1(config-if)# standby 1 priority 255
R1(config-if)# standby 1 preempt
R1(config-if)# no shutdown - R1(config-if)# ip address 192.168.1.100 255.255.255.0
R1(config-if)# standby 1 ip 192.168.1.1
R1(config-if)# standby 1 priority 150
R1(config-if)# no shutdown
- R1(config-if)# ip address 192.168.1.100 255.255.255.0
-
23. Question
Fill in the blank.
In FHRP operation, two or more routers are represented as a single virtual router. -
24. Question
Match the description to the correct command. (Not all options are used.)
CCNA2 v6.0 Chapter 4 Exam 01
-
25. Question
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
What are two reasons why the ping messages that are issued from Laptop0 towards Laptop1 are failing? (Choose two.)