CCNA3 Chapter 10 Exam - Online Assessment
Quiz-summary
0 of 23 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
Information
CCNA3 Chapter 10 Exam – Online Assessment
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 23 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Average score |
|
Your score |
|
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- Answered
- Review
-
Question 1 of 23
1. Question
A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?Correct
Incorrect
-
Question 2 of 23
2. Question
Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)
CCNA3 v6.0 Chapter 10 Exam 009
Correct
Incorrect
-
Question 3 of 23
3. Question
Refer to the exhibit. Which conclusion can be drawn from this OSPF multiaccess network?
CCNA3 v6.0 Chapter 10 Exam 007
Correct
Incorrect
-
Question 4 of 23
4. Question
Which OSPF feature allows a remote OSPF area to participate in OSPF routing when it cannot connect directly to OSPF Area 0?Correct
Incorrect
-
Question 5 of 23
5. Question
Refer to the exhibit. What are three resulting DR and BDR elections for the given topology? (Choose three.)
CCNA3 v6.0 Chapter 10 Exam 008
Correct
Incorrect
-
Question 6 of 23
6. Question
When checking a routing table, a network technician notices the following entry:O*E2 0.0.0.0/0 [110/1] via 192.168.16.3, 00:20:22, Serial0/0/0
What information can be gathered from this output?
Correct
Incorrect
-
Question 7 of 23
7. Question
Refer to the exhibit. What two conclusions can be drawn based on the output of the show ipv6 route command? (Choose two.)
CCNA3 v6.0 Chapter 10 Exam 002
Correct
Incorrect
-
Question 8 of 23
8. Question
Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?Correct
Incorrect
-
Question 9 of 23
9. Question
A network engineer suspects that OSPFv3 routers are not forming neighbor adjacencies because there are interface timer mismatches. Which two commands can be issued on the interface of each OSFPv3 router to resolve all timer mismatches? (Choose two.)Correct
Incorrect
-
Question 10 of 23
10. Question
A network engineer has manually configured the hello interval to 15 seconds on an interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be affected?Correct
Incorrect
-
Question 11 of 23
11. Question
Which command can be used to view the OSPF hello and dead time intervals?Correct
Incorrect
-
Question 12 of 23
12. Question
Refer to the exhibit. A network administrator is configuring OSPF for R1 and R2, but the adjacency cannot be established. What is the cause of the issue?
CCNA3 v6.0 Chapter 10 Exam 005
Correct
Incorrect
-
Question 13 of 23
13. Question
Refer to the exhibit. What the amount of time that has elapsed since the router received a hello packet?
CCNA3 v6.0 Chapter 10 Exam 004
Correct
Incorrect
-
Question 14 of 23
14. Question
Which two parameters must match between neighboring OSPF routers in order to form an adjacency? (Choose two.)Correct
Incorrect
-
Question 15 of 23
15. Question
Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem?
CCNA3 v6.0 Chapter 10 Exam 006
Correct
Incorrect
-
Question 16 of 23
16. Question
Refer to the exhibit. R1 and R2 are connected to the same LAN segment and are configured to run OSPFv3. They are not forming a neighbor adjacency. What is the cause of the problem?
CCNA3 v6.0 Chapter 10 Exam 001
Correct
Incorrect
-
Question 17 of 23
17. Question
A network administrator is troubleshooting an OSPFv3 configuration on an IPv6 network. The administrator issues the show ipv6 protocols command. What is the purpose for this command?Correct
Incorrect
-
Question 18 of 23
18. Question
Refer to the exhibit. Directly connected networks configured on router R1 are not being shared with neighboring routers through OSPFv3. What is the cause of the issue?
Correct
Incorrect
-
Question 19 of 23
19. Question
An administrator is troubleshooting OSPFv3 adjacency issues. Which command would the administrator use to confirm that OSPFv3 hello and dead intervals are matching between routers?Correct
Incorrect
-
Question 20 of 23
20. Question
What three states are transient OPSF neighbor states that indicate a stable adjacency is not yet formed between two routers? (Choose three.)Correct
Incorrect
-
Question 21 of 23
21. Question
Match each OSPF election criterion to its sequential order for the OSPF DR and BDR election process. (Not all options are used.)
Sort elements
- Elect the router with the highest IPv4 address on loopback interfaces.
- Elect the router with the highest manually configured router ID.
- Elect the router with the highest routing process ID.
- Elect the router with the highest interface priority.
- Elect the router with the highest active IPv4 address on physical interfaces.
-
third
-
second
-
first
-
fourth
Correct
Incorrect
-
Question 22 of 23
22. Question
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which routers are the DR and BDR in this topology?
Correct
Incorrect
-
Question 23 of 23
23. Question
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
A network administrator is configuring multiarea OSPFv3 on the routers. The routing design requires that the router RT1 is a DROTHER for the network in Area 0 and the DR for the network in Area 1. Check the settings and status of the routers. What can the administrator do to ensure that RT1 will meet the design requirement after all routers restart?
Correct
Incorrect