CCNA2 Chapter 5 Exam - Online Assessment
Quiz-summary
0 of 24 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
Information
CCNA2 Chapter 5 Exam – Online Assessment
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 24 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
Average score |
|
Your score |
|
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- Answered
- Review
-
Question 1 of 24
1. Question
Which statement describes the port speed LED on the Cisco Catalyst 2960 switch?Correct
Incorrect
-
Question 2 of 24
2. Question
Which command is used to set the BOOT environment variable that defines where to find the IOS image file on a switch?Correct
Incorrect
-
Question 3 of 24
3. Question
What is a function of the switch boot loader?Correct
Incorrect
-
Question 4 of 24
4. Question
Which interface is the default location that would contain the IP address used to manage a 24-port Ethernet switch?Correct
Incorrect
-
Question 5 of 24
5. Question
A production switch is reloaded and finishes with a Switch> prompt. What two facts can be determined? (Choose two.)Correct
Incorrect
-
Question 6 of 24
6. Question
Which two statements are true about using full-duplex Fast Ethernet? (Choose two.)Correct
Incorrect
-
Question 7 of 24
7. Question
In which situation would a technician use the show interfaces switch command?Correct
Incorrect
-
Question 8 of 24
8. Question
Refer to the exhibit. A network technician is troubleshooting connectivity issues in an Ethernet network with the command show interfaces fastEthernet 0/0. What conclusion can be drawn based on the partial output in the exhibit?
CCNA2 v6.0 Chapter 5 Exam 004
Correct
Incorrect
-
Question 9 of 24
9. Question
Refer to the exhibit. What media issue might exist on the link connected to Fa0/1 based on the show interface command?
CCNA2 v6.0 Chapter 5 Exam 002
Correct
Incorrect
-
Question 10 of 24
10. Question
If one end of an Ethernet connection is configured for full duplex and the other end of the connection is configured for half duplex, where would late collisions be observed?Correct
Incorrect
-
Question 11 of 24
11. Question
What is one difference between using Telnet or SSH to connect to a network device for management purposes?Correct
Incorrect
-
Question 12 of 24
12. Question
Refer to the exhibit. The network administrator wants to configure Switch1 to allow SSH connections and prohibit Telnet connections. How should the network administrator change the displayed configuration to satisfy the requirement?
CCNA2 v6.0 Chapter 5 Exam 001
Correct
Incorrect
-
Question 13 of 24
13. Question
What is the effect of using the switchport port-security command?Correct
Incorrect
-
Question 14 of 24
14. Question
Where are dynamically learned MAC addresses stored when sticky learning is enabled with the switchport port-security mac-address sticky command?Correct
Incorrect
-
Question 15 of 24
15. Question
A network administrator configures the port security feature on a switch. The security policy specifies that each access port should allow up to two MAC addresses. When the maximum number of MAC addresses is reached, a frame with the unknown source MAC address is dropped and a notification is sent to the syslog server. Which security violation mode should be configured for each access port?Correct
Incorrect
-
Question 16 of 24
16. Question
Which two statements are true regarding switch port security? (Choose two.)Correct
Incorrect
-
Question 17 of 24
17. Question
Which action will bring an error-disabled switch port back to an operational state?Correct
Incorrect
-
Question 18 of 24
18. Question
Refer to the exhibit. Port Fa0/2 has already been configured appropriately. The IP phone and PC work properly. Which switch configuration would be most appropriate for port Fa0/2 if the network administrator has the following goals?
- No one is allowed to disconnect the IP phone or the PC and connect some other wired device.
- If a different device is connected, port Fa0/2 is shut down.
- The switch should automatically detect the MAC address of the IP phone and the PC and add those addresses to the running configuration.
CCNA2 v6.0 Chapter 5 Exam 006
Correct
Incorrect
-
Question 19 of 24
19. Question
Refer to the exhibit. What can be determined about port security from the information that is shown
CCNA2 v6.0 Chapter 5 Exam 005
Correct
Incorrect
-
Question 20 of 24
20. Question
Refer to the exhibit. Which event will take place if there is a port security violation on switch S1 interface Fa0/1?
CCNA2 v6.0 Chapter 5 Exam 003
Correct
Incorrect
-
Question 21 of 24
21. Question
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which event will take place if there is a port security violation on switch S1 interface Fa0/1?Correct
Incorrect
-
Question 22 of 24
22. Question
Math the step to each switch boot sequence description. (Not all options are used.)
Sort elements
- CPU register initializations
- enter global configuration mode
- execute POST
- flash file system initialization
- load the boot loader from ROM
- load the IOS
- transfer switch control to the IOS
-
step 3
-
step 1
-
step 4
-
step 2
-
step 5
-
step 6
Correct
Incorrect
-
Question 23 of 24
23. Question
Identify the steps needed to configure a switch for SSH. The answer order does not matter. (Not all options are used.)
Sort elements
- Create a local user.
- Generate RSA keys.
- Configure a domain name.
- Use the login local command.
- Use the transport input ssh command.
- Use the login command.
- Use the password cisco commnad.
-
SSH configuration step
-
SSH configuration step
-
SSH configuration step
-
SSH configuration step
-
SSH configuration step
Correct
Incorrect
-
Question 24 of 24
24. Question
Match the link state to the interface and protocol status. (Not all options are used.)
Sort elements
- administratively down
- down/down
- up/disabled
- up/down
- up/up
-
disabled
-
layer 1 problem
-
Layer 2 problem
-
operational
Correct
Incorrect