CCNA2 Chapter 4 Exam – Online Assessment

1. Question

A network designer must provide a rationale to a customer for a design which will move an enterprise from a flat network topology to a hierarchical network topology. Which two features of the hierarchical design make it the better choice? (Choose two.)

lower bandwidth requirements
reduced cost for equipment and user training
easier to provide redundant links to ensure higher availability
less required equipment to provide the same performance levels
simpler deployment for additional switch equipment

2. Question

What is a collapsed core in a network design?

a combination of the functionality of the access and distribution layers
a combination of the functionality of the distribution and core layers
a combination of the functionality of the access and core layers
a combination of the functionality of the access, distribution, and core layers

3. Question

What is a definition of a two-tier LAN network design?

access and core layers collapsed into one tier, and the distribution layer on a separate tier
access and distribution layers collapsed into one tier, and the core layer on a separate tier
distribution and core layers collapsed into one tier, and the access layer on a separate tier
access, distribution, and core layers collapsed into one tier, with a separate backbone layer

4. Question

What is a basic function of the Cisco Borderless Architecture distribution layer?

acting as a backbone
aggregating all the campus blocks
aggregating Layer 3 routing boundaries
providing access to end user devices

5. Question

Which two previously independent technologies should a network administrator attempt to combine after choosing to upgrade to a converged network infrastructure? (Choose two.)

user data traffic
VoIP phone traffic
scanners and printers
mobile cell phone traffic
electrical system

6. Question

A local law firm is redesigning the company network so that all 20 employees can be connected to a LAN and to the Internet. The law firm would prefer a low cost and easy solution for the project. What type of switch should be selected?

fixed configuration
modular configuration
stackable configuration
StackPower
StackWise

7. Question

What are two advantages of modular switches over fixed-configuration switches? (Choose two.)

lower cost per switch
increased scalability
lower forwarding rates
need for fewer power outlets
availability of multiple ports for bandwidth aggregation

8. Question

Which type of address does a switch use to build the MAC address table?

destination IP address
source IP address
destination MAC address
source MAC address

9. Question

Which network device can be used to eliminate collisions on an Ethernet network?

firewall
hub
router
switch

10. Question

What two criteria are used by a Cisco LAN switch to decide how to forward Ethernet frames? (Choose two.)

path cost
egress port
ingress port
destination IP address
destination MAC address

11. Question

Refer to the exhibit. Consider that the main power has just been restored. PC3 issues a broadcast IPv4 DHCP request. To which port will SW1 forward this request?

CCNA2 v6.0 Chapter 4 Exam 001

to Fa0/1 only
to Fa0/1 and Fa0/2 only
to Fa0/1, Fa0/2, and Fa0/3 only
to Fa0/1, Fa0/2, Fa0/3, and Fa0/4
to Fa0/1, Fa0/2, and Fa0/4 only

12. Question

What is one function of a Layer 2 switch?

forwards data based on logical addressing
duplicates the electrical signal of each frame to every port
learns the port assigned to a host by examining the destination MAC address
determines which interface is used to forward a frame based on the destination MAC address

13. Question

Refer to the exhibit. How is a frame sent from PCA forwarded to PCC if the MAC address table on switch SW1 is empty?

CCNA2 v6.0 Chapter 4 Exam 002

SW1 floods the frame on all ports on the switch, excluding the interconnected port to switch SW2 and the port through which the frame entered the switch.
SW1 floods the frame on all ports on SW1, excluding the port through which the frame entered the switch.
SW1 forwards the frame directly to SW2. SW2 floods the frame to all ports connected to SW2, excluding the port through which the frame entered the switch.
SW1 drops the frame because it does not know the destination MAC address.

14. Question

A small publishing company has a network design such that when a broadcast is sent on the LAN, 200 devices receive the transmitted broadcast. How can the network administrator reduce the number of devices that receive broadcast traffic?

Add more switches so that fewer devices are on a particular switch.
Replace the switches with switches that have more ports per switch. This will allow more devices on a particular switch.
Segment the LAN into smaller LANs and route between them.
Replace at least half of the switches with hubs to reduce the size of the broadcast domain.

15. Question

Refer to the exhibit. How many broadcast domains are displayed?

CCNA2 v6.0 Chapter 4 Exam 003

1
4
8
16
55

16. Question

Which solution would help a college alleviate network congestion due to collisions?

a firewall that connects to two Internet providers
a high port density switch
a router with two Ethernet ports
a router with three Ethernet ports

17. Question

Which network device can serve as a boundary to divide a Layer 2 broadcast domain?

router
Ethernet bridge
Ethernet hub
access point

18. Question

What is the destination address in the header of a broadcast frame?

0.0.0.0
255.255.255.255
11-11-11-11-11-11
FF-FF-FF-FF-FF-FF

19. Question

Which statement describes a result after multiple Cisco LAN switches are interconnected?

The broadcast domain expands to all switches.
One collision domain exists per switch.
Frame collisions increase on the segments connecting the switches.
There is one broadcast domain and one collision domain per switch.

20. Question

What does the term “port density” represent for an Ethernet switch?

the memory space that is allocated to each switch port
the number of available ports
the numbers of hosts that are connected to each switch port
the speed of each port

21. Question

What are two reasons a network administrator would segment a network with a Layer 2 switch? (Choose two.)

to create fewer collision domains
to enhance user bandwidth
to create more broadcast domains
to eliminate virtual circuits
to isolate traffic between segments
to isolate ARP request messages from the rest of the network

22. Question

Fill in the blank.
A ……………………….. network is one that uses the same infrastructure to carry voice, data, and video signals.

23. Question

Match the borderless switched network guideline description to the principles. (Not all options are used.)

Sort elements

convergence
flexibility
hierarchical
modularity
resiliency

allows intelligent traffic load sharing by using all network resources
facilitates understanding the role of each device at every tier, simplifies deployment, operation, management, and reduces fault domains at every tier
allows seamless network expansion and integrated service enablement on an on-demand basis
satisfies user expectations for keeping the network always on

24. Question

Match the functions to the corresponding layers. (Not all options are used.)

Sort elements

represents the network edge
provides network access to the user
implements network access policy
establishes Layer 3 routing boundaries
provides high-speed backbone connectivity
functions as an aggregator for all the campus blocks
implements personal firewalls on the client computers

access layer Target
access layer Target
distribution layer
distribution layer
core layer
core layer

25. Question

Match the forwarding characteristic to its type. (Not all options are used.)

Sort elements

appropriate for high performance computing applications
forwarding process can begin after receiving the destination address
may forward invalid frame
error checking before forwarding
forwarding process only begins after receiving the entire frame
only forwards valid frames

cute-through Target
cute-through Target
cute-through Target
store-and-forward
store-and-forward
store-and-forward

CCNA2 Chapter 4 Exam – Online Assessment