CCNA2 Chapter 10 Exam - Online Assessment

1. Question

A ping fails when performed from router R1 to directly connected router R2. The network administrator then proceeds to issue the show cdp neighbors command. Why would the network administrator issue this command if the ping failed between the two routers?

The network administrator suspects a virus because the ping command did not work.
The network administrator wants to verify Layer 2 connectivity.
The network administrator wants to verify the IP address configured on router R2.
The network administrator wants to determine if connectivity can be established from a non-directly connected network.

2. Question

Which statement is true about CDP on a Cisco device?

The show cdp neighbor detail command will reveal the IP address of a neighbor only if there is Layer 3 connectivity.
To disable CDP globally, the no cdp enable command in interface configuration mode must be used.
CDP can be disabled globally or on a specific interface.
Because it runs at the data link layer, the CDP protocol can only be implemented in switches.

3. Question

Why would a network administrator issue the show cdp neigbors command on a router?

to display device ID and other information about directly connected Cisco devices
to display router ID and other information about OSPF neighbors
to display line status and other information about directly connected Cisco devices
to display routing table and other information about directly connected Cisco devices

4. Question

Refer to the exhibit. Routers R1 and R2 are connected via a serial link. One router is configured as the NTP master, and the other is an NTP client. Which two pieces of information can be obtained from the partial output of the show ntp associations detail command on R2? (Choose two.)

CCNA2 v6.0 Chapter 10 Exam 001

Both routers are configured to use NTPv2.
Router R1 is the master, and R2 is the client.
Router R2 is the master, and R1 is the client.
The IP address of R1 is 192.168.1.2.
The IP address of R2 is 192.168.1.2.

5. Question

Which two statements are true about NTP servers in an enterprise network? (Choose two.)

There can only be one NTP server on an enterprise network.
All NTP servers synchronize directly to a stratum 1 time source.
NTP servers at stratum 1 are directly connected to an authoritative time source.
NTP servers ensure an accurate time stamp on logging and debugging information.
NTP servers control the mean time between failures (MTBF) for key network devices.

6. Question

The command ntp server 10.1.1.1 is issued on a router. What impact does this command have?

determines which server to send system log files to
identifies the server on which to store backup configurations
ensures that all logging will have a time stamp associated with it
synchronizes the system clock with the time source with IP address 10.1.1.1

7. Question

Refer to the exhibit. Which two conclusions can be drawn from the syslog message that was generated by the router? (Choose two.)

CCNA2 v6.0 Chapter 10 Exam 002

This message resulted from an unusual error requiring reconfiguration of the interface.
This message indicates that the interface should be replaced.
This message is a level 5 notification message.
This message indicates that service timestamps have been configured.
This message indicates that the interface changed state five times.

8. Question

Which protocol or service allows network administrators to receive system messages that are provided by network devices?

syslog
NTP
SNMP
NetFlow

9. Question

Which syslog message type is accessible only to an administrator and only via the Cisco CLI?

errors
debugging
emergency
alerts

10. Question

Refer to the exhibit. From what location have the syslog messages been retrieved?

CCNA2 v6.0 Chapter 10 Exam 004

syslog server
syslog client
router RAM
router NVRAM

11. Question

Refer to the exhibit. What does the number 17:46:26.143 represent?

CCNA2 v6.0 Chapter 10 Exam 003

the time passed since the syslog server has been started
the time when the syslog message was issued
the time passed since the interfaces have been up
the time on the router when the show logging command was issued

12. Question

What is used as the default event logging destination for Cisco routers and switches?

terminal line
syslog server
console line
workstation

13. Question

A network administrator has issued the logging trap 4 global configuration mode command. What is the result of this command?

After four events, the syslog client will send an event message to the syslog server.
The syslog client will send to the syslog server any event message that has a severity level of 4 and higher.
The syslog client will send to the syslog server any event message that has a severity level of 4 and lower.
The syslog client will send to the syslog server event messages with an identification trap level of only 4.

14. Question

What is the major release number in the IOS image name c1900-universalk9-mz.SPA.152-3.T.bin?

2
3
15
52
1900

15. Question

What statement describes a Cisco IOS image with the “universalk9_npe” designation for Cisco ISR G2 routers?

It is an IOS version that can only be used in the United States of America.
It is an IOS version that provides only the IPBase feature set.
It is an IOS version that offers all of the Cisco IOS Software feature sets.
It is an IOS version that, at the request of some countries, removes any strong cryptographic functionality.

16. Question

What code in the Cisco IOS 15 image filename c1900-universalk9-mz.SPA.153-3.M.bin indicates that the file is digitally signed by Cisco?

SPA
universalk9
M
mz

17. Question

Which two conditions should the network administrator verify before attempting to upgrade a Cisco IOS image using a TFTP server? (Choose two.)

Verify the name of the TFTP server using the show hosts command.
Verify that the TFTP server is running using the tftpdnld command.
Verify that the checksum for the image is valid using the show version command.
Verify connectivity between the router and TFTP server using the ping command.
Verify that there is enough flash memory for the new Cisco IOS image using the show flash command.

18. Question

A network administrator configures a router with the command sequence:

R1(config)# boot system tftp://c1900-universalk9-mz.SPA.152-4.M3.bin
R1(config)# boot system rom

What is the effect of the command sequence?

On next reboot, the router will load the IOS image from ROM.
The router will copy the IOS image from the TFTP server and then reboot the system.
The router will load IOS from the TFTP server. If the image fails to load, it will load the IOS image from ROM.
The router will search and load a valid IOS image in the sequence of flash, TFTP, and ROM.

19. Question

A network engineer is upgrading the Cisco IOS image on a 2900 series ISR. What command could the engineer use to verify the total amount of flash memory as well as how much flash memory is currently available?

show flash0:
show version
show interfaces
show startup-config

20. Question

Beginning with the Cisco IOS Software Release 15.0, which license is a prerequisite for installing additional technology pack licenses?

IPBase
DATA
UC
SEC

21. Question

Which three software packages are available for Cisco IOS Release 15.0?

DATA
IPVoice
Security
Enterprise Services
Unified Communications
Advanced IP Services

22. Question

When a customer purchases a Cisco IOS 15.0 software package, what serves as the receipt for that customer and is used to obtain the license as well?

Software Claim Certificate
End User License Agreement
Unique Device Identifier
Product Activation Key

23. Question

In addition to IPBase, what are the three technology packs that are shipped within the universal Cisco IOS Software Release 15 image? (Choose three.)

Advanced IP Services
Advanced Enterprise Services
DATA
Security
SP Services
Unified Communications

24. Question

Which command would a network engineer use to find the unique device identifier of a Cisco router?

show version
show license udi
show running-configuration
license install stored-location-url

25. Question

Which command is used to configure a one-time acceptance of the EULA for all Cisco IOS software packages and features?

license save
show license
license boot module module-name
license accept end user agreement

26. Question

Refer to the exhibit. Match the components of the IOS image name to their description. (Not all options are used.)

CCNA2 v6.0 Chapter 10 Exam 005

Sort elements

specifying the feature set
minor release number
where the image runs and if the file is compressed
platform on which the image runs
authentication type
maintenance release and rebuild number
new feature release number
file extension
major release number

universalk9

1

mz

c1900

M4

4

bin

15

CCNA2 Chapter 10 Exam – Online Assessment