CCNA1 Chapter 4 Exam - Online Assessment

1. Question

What are two reasons for physical layer protocols to use frame encoding techniques? (Choose two.)

to reduce the number of collisions on the media
to distinguish data bits from control bits
to provide better media error correction
to identify where the frame starts and ends
to increase the media throughput

2. Question

What is indicated by the term throughput?

the guaranteed data transfer rate offered by an ISP
the capacity of a particular medium to carry data
the measure of the usable data transferred across the media
the measure of the bits transferred across the media over a given period of time
the time it takes for a message to get from sender to receiver

3. Question

A network administrator notices that some newly installed Ethernet cabling is carrying corrupt and distorted data signals. The new cabling was installed in the ceiling close to fluorescent lights and electrical equipment. Which two factors may interfere with the copper cabling and result in signal distortion and data corruption? (Choose two.)

EMI
crosstalk
RFI
signal attenuation
extended length of cabling

4. Question

Which characteristic describes crosstalk?

the distortion of the network signal from fluorescent lighting
the distortion of the transmitted messages from signals carried in adjacent wires
the weakening of the network signal over long cable lengths
the loss of wireless signal over excessive distance from the access point

5. Question

What technique is used with UTP cable to help protect against signal interference from crosstalk?

twisting the wires together into pairs
wrapping a foil shield around the wire pairs
encasing the cables within a flexible plastic sheath
terminating the cable with special grounded connectors

6. Question

Refer to the exhibit. The PC is connected to the console port of the switch. All the other connections are made through FastEthernet links. Which types of UTP cables can be used to connect the devices?

CCNA1 v6.0 Chapter 4 Exam 002

1 - rollover, 2 - crossover, 3 - straight-through
1 - rollover, 2 - straight-through, 3 - crossover
1 - crossover, 2 - straight-through, 3 - rollover
1 - crossover, 2 - rollover, 3 - straight-through

7. Question

Refer to the exhibit. What is wrong with the displayed termination?

CCNA1 v6.0 Chapter 4 Exam 001

The woven copper braid should not have been removed.
The wrong type of connector is being used.
The untwisted length of each wire is too long.
The wires are too thick for the connector that is used.

8. Question

Which type of connector does a network interface card use?

DIN
PS-2
RJ-11
RJ-45

9. Question

What is one advantage of using fiber optic cabling rather than copper cabling?

It is usually cheaper than copper cabling.
It is able to be installed around sharp bends.
It is easier to terminate and install than copper cabling.
It is able to carry signals much farther than copper cabling.

10. Question

Why are two strands of fiber used for a single fiber optic connection?

The two strands allow the data to travel for longer distances without degrading.
They prevent crosstalk from causing interference on the connection.
They increase the speed at which the data can travel.
They allow for full-duplex connectivity.

11. Question

A network administrator is designing the layout of a new wireless network. Which three areas of concern should be accounted for when building a wireless network? (Choose three.)

mobility options
security
interference
coverage area
extensive cabling
packet collision

12. Question

Which layer of the OSI model is responsible for specifying the encapsulation method used for specific types of media?

application
transport
data link
physical

13. Question

What are two services performed by the data link layer of the OSI model? (Choose two.)

It encrypts data packets.
It determines the path to forward packets.
It accepts Layer 3 packets and encapsulates them into frames.
It provides media access control and performs error detection.
It monitors the Layer 2 communication by building a MAC address table.

14. Question

What is true concerning physical and logical topologies?

The logical topology is always the same as the physical topology.
Physical topologies are concerned with how a network transfers frames.
Physical topologies display the IP addressing scheme of each network.
Logical topologies refer to how a network transfers data between devices.

15. Question

Which method of data transfer allows information to be sent and received at the same time?

full duplex
half duplex
multiplex
simplex

16. Question

Which statement describes an extended star topology?

End devices connect to a central intermediate device, which in turn connects to other central intermediate devices.
End devices are connected together by a bus and each bus connects to a central intermediate device.
Each end system is connected to its respective neighbor via an intermediate device.
All end and intermediate devices are connected in a chain to each other.

17. Question

What is contained in the trailer of a data-link frame?

logical address
physical address
data
error detection

18. Question

As data travels on the media in a stream of 1s and 0s how does a receiving node identify the beginning and end of a frame?

The transmitting node inserts start and stop bits into the frame.
The transmitting node sends a beacon to notify that a data frame is attached.
The receiving node identifies the beginning of a frame by seeing a physical address.
The transmitting node sends an out-of-band signal to the receiver about the beginning of the frame.

19. Question

What is the function of the CRC value that is found in the FCS field of a frame?

to verify the integrity of the received frame
to verify the physical address in the frame
to verify the logical address in the frame
to compute the checksum header for the data field in the frame

20. Question

Fill in the blank.
The term ……………………… indicates the capacity of a medium to carry data and it is typically measured in kilobits per second (kb/s) or megabits per second (Mb/s).

21. Question

Fill in the blank.
What acronym is used to reference the data link sublayer that identifies the network layer protocol encapsulated in the frame? …………………

22. Question

Fill in the blank.
A physical topology that is a variation or combination of a point-to-point, hub and spoke, or mesh topology is commonly known as a ……………….. topology.

23. Question

Match the characteristics to the correct type of fiber. (Not all options are used.)

Sort elements

LED as light source
several paths of light into the fiber
generally used with LANs
only one ray of light into the fiber
generally use with Campus backbone
laser as light source
supports full-duplex operation

Multimode Fiber
Multimode Fiber
Multimode Fiber
Single-mode Fiber
Single-mode Fiber
Single-mode Fiber

24. Question

What is the definition of bandwidth?

the measure of the transfer of bits across the media over a given period of time
the speed at which bits travel on the network
the amount of data that can flow from one place to another in a given amount of time
the measure of usable data transferred over a given period of time

25. Question

What is a role of the Logical Link Control sublayer?

to provide access to various Layer 1 network technologies
to provide data link layer addressing
to define the media access processes performed by network hardware
to mark frames to identify the network layer protocol being carried

26. Question

What are two examples of hybrid topologies? (Choose two.)

partial mesh
extended star
hub and spoke
point-to-point
full mesh

CCNA1 Chapter 4 Exam – Online Assessment