11.6.2 Lab – Switch Security Configuration Answers

11.6.2 Lab – Switch Security Configuration Answers

Lab – Switch Security Configuration (Answers Version)

Answers Note: Red font color or gray highlights indicate text that appears in the Answers copy only.

Topology

The topology has 1 router, 2 switches and 2 PCs. The router R1 has 2 interfaces: Lo0 and G0/0/1. R1 G0/0/1 is connected F0/5 on S1. S1 F0/6 is connected to PC-A. S1 F0/1 is connected S2 F0/1. S2 F0/18 is connected to PC-B.

Addressing Table

Device

Interface / VLAN

IP Address

Subnet Mask

R1

G0/0/1

192.168.10.1

255.255.255.0

R1

Loopback 0

10.10.1.1

255.255.255.0

S1

VLAN 10

192.168.10.201

255.255.255.0

S2

VLAN 10

192.168.10.202

255.255.255.0

PC – A

NIC

DHCP

255.255.255.0

PC – B

NIC

DHCP

255.255.255.0

Objectives

Part 1: Configure the Network Devices.

  • Cable the network.
  • Configure R1.
  • Configure and verify basic switch settings.

Part 2: Configure VLANs on Switches.

  • Configure VLAN 10.
  • Configure the SVI for VLAN 10.
  • Configure VLAN 333 with the name Native on S1 and S2.
  • Configure VLAN 999 with the name ParkingLot on S1 and S2.

Part 3: Configure Switch Security.

  • Implement 802.1Q trunking.
  • Configure access ports.
  • Secure and disable unused switchports.
  • Document and implement port security features.
  • Implement DHCP snooping security.
  • Implement PortFast and BPDU guard.
  • Verify end-to-end-connectivity.

Background / Scenario

This is a comprehensive lab to review previously covered Layer 2 security features.

Note: The routers used with CCNA hands-on labs are Cisco 4221 with Cisco IOS XE Release 16.9.3 (universalk9 image). The switches used in the labs are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and the output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers.

Note: Make sure that the switches have been erased and have no startup configurations. If you are unsure, contact your Answers.

Answers Note: Refer to the Answers Lab Manual for the procedures to initialize and reload devices.

Required Resources

  • 1 Router (Cisco 4221 with Cisco IOS XE Release 16.9.3 universal image or comparable)
  • 2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)
  • 2 PCs (Windows with a terminal emulation program, such as Tera Term)
  • Console cables to configure the Cisco IOS devices via the console ports
  • Ethernet cables as shown in the topology

Instructions

Part 1:  Configure the Network Devices.

Step 1:  Cable the network.

  1. Cable the network as shown in the topology.
  2. Initialize the devices.

Step 2:  Configure R1.

  1. Load the following configuration script on R1.

Open configuration window

enable

configure terminal

hostname R1

no ip domain lookup

ip dhcp excluded-address 192.168.10.1 192.168.10.9

ip dhcp excluded-address 192.168.10.201 192.168.10.202

!

ip dhcp pool Students

 network 192.168.10.0 255.255.255.0

 default-router 192.168.10.1

 domain-name CCNA2.Lab-11.6.1

!

interface Loopback0

 ip address 10.10.1.1 255.255.255.0

!

interface GigabitEthernet0/0/1

 description Link to S1 Port 5

 ip dhcp relay information trusted

 ip address 192.168.10.1 255.255.255.0

 no shutdown

!

line con 0

 logging synchronous

 exec-timeout 0 0

  1. Verify the running-configuration on R1 using the following command:

R1# show ip interface brief

Interface              IP-Address      OK? Method Status                Protocol

GigabitEthernet0/0/0   unassigned      YES unset  down                  down

GigabitEthernet0/0/1   192.168.10.1    YES manual up                    up

Loopback0              10.10.1.1       YES manual up                    up

  1. Verify IP addressing and interfaces are in an up / up state (troubleshoot as necessary).

Close configuration window

Step 3:  Configure and verify basic switch settings.

  1. Configure the hostname for switches S1 and S2.

Open configuration window

Switch# config t

Switch(config)# hostname S1

Open configuration window

Switch# config t

Switch(config)# hostname S2

  1. Prevent unwanted DNS lookups on both switches.

S1(config)# no ip domain-lookup

S2(config)# no ip domain-lookup

  1. Configure interface descriptions for the ports that are in use in S1 and S2.

S1(config)# interface f0/1

S1(config-if)# description Link to S2

S1(configif)# interface f0/5

S1(config-if)# description Link to R1

S1(configif)# interface f0/6

S1(config-if)# description Link to PC-A

 

S2(config)# interface f0/1

S2(config-if)# description Link to S1

S2(configif)# interface f0/18

S2(config-if)# description Link to PC-B

  1. Set the default-gateway for the Management VLAN to 192.168.10.1 on both switches.

S1(config)# ip default-gateway 192.168.10.1

S2(config)# ip default-gateway 192.168.10.1

Part 2:  Configure VLANs on Switches.

Step 1:  Configure VLAN 10.

Add VLAN 10 to S1 and S2 and name the VLAN Management.

S1(config)# vlan 10

S1(config-vlan)# name Management

 

S2(config)# vlan 10

S2(config-vlan)# name Management

Step 2:  Configure the SVI for VLAN 10.

Configure the IP address according to the Addressing Table for SVI for VLAN 10 on S1 and S2. Enable the SVI interfaces and provide a description for the interface.

S1(config)# interface vlan 10

S1(config-if)# ip address 192.168.10.201 255.255.255.0

S1(config-if)# description Management SVI

S1(config-if)# no shutdown

 

S2(config)# interface vlan 10

S2(config-if)# ip address 192.168.10.202 255.255.255.0

2S1(config-if)# description Management SVI

S2(config-if)# no shutdown

Step 3:  Configure VLAN 333 with the name Native on S1 and S2.

S1(config)# vlan 333

S1(config-vlan)# name Native

 

S2(config)# vlan 333

S2(config-vlan)# name Native

Step 4:  Configure VLAN 999 with the name ParkingLot on S1 and S2.

S1(config-vlan)# vlan 999

S1(config-vlan)# name ParkingLot

 

S2(config-vlan)# vlan 999

S2(config-vlan)# name ParkingLot

Part 3:  Configure Switch Security.

Step 1:  Implement 802.1Q trunking.

  1. On both switches, configure trunking on F0/1 to use VLAN 333 as the native VLAN.

S1(config)# interface f0/1

S1(config-if)# switchport mode trunk

S1(config-if)# switchport trunk native vlan 333

 

S2(config)# interface f0/1

S2(config-if)# switchport mode trunk

S2(config-if)# switchport trunk native vlan 333

  1. Verify that trunking is configured on both switches.

S1# show interface trunk

 

Port        Mode             Encapsulation  Status        Native vlan

Fa0/1       on               802.1q         trunking      333

 

Port        Vlans allowed on trunk

Fa0/1       1-4094

 

Port        Vlans allowed and active in management domain

Fa0/1       1,10,333,999

 

Port        Vlans in spanning tree forwarding state and not pruned

Fa0/1       1,10,333,999

 

S2# show interface trunk

 

Port        Mode             Encapsulation  Status        Native vlan

Fa0/1       on               802.1q         trunking      333

 

Port        Vlans allowed on trunk

Fa0/1       1-4094

 

Port        Vlans allowed and active in management domain

Fa0/1       1,10,333,999

 

Port        Vlans in spanning tree forwarding state and not pruned

Fa0/1       1,10,333,999

  1. Disable DTP negotiation on F0/1 on S1 and S2.

S1(config)# interface f0/1

S1(config-if)# switchport nonegotiate

 

S2(config)# interface f0/1

S2(config-if)# switchport nonegotiate

  1. Verify with the show interfaces command.

S1# show interfaces f0/1 switchport | include Negotiation

Negotiation of Trunking: Off

 

S2# show interfaces f0/1 switchport | include Negotiation

Negotiation of Trunking: Off

Step 2:  Configure access ports.

  1. On S1, configure F0/5 and F0/6 as access ports that are associated with VLAN 10.

S1(config)# interface range f0/5 – 6

S1(config-if)# switchport mode access

S1(config-if)# switchport access vlan 10

  1. On S2, configure F0/18 as an access port that is associated with VLAN 10.

S2(config)# interface f0/18

S2(config-if)# switchport mode access

S2(config-if)# switchport access vlan 10

Step 3:  Secure and disable unused switchports.

  1. On S1 and S2, move the unused ports from VLAN 1 to VLAN 999 and disable the unused ports.

S1(config)# interface range f0/2-4 , f0/7-24, g0/1-2

S1(config-if-range)# switchport mode access

S1(config-if-range)# switchport access vlan 999

S1(config-if-range)# shutdown

 

S2(config)# interface range f0/2-17 , f0/19-24, g0/1-2

S2(config-if-range)# switchport mode access

S2(config-if-range)# switchport access vlan 999

S2(config-if-range)# shutdown

  1. Verify that unused ports are disabled and associated with VLAN 999 by issuing the show command.

S1# show interfaces status

 

Port      Name               Status       Vlan       Duplex  Speed Type

Fa0/1     Link to S2         connected    trunk      a-full  a-100 10/100BaseTX

Fa0/2                        disabled     999          auto   auto 10/100BaseTX

Fa0/3                        disabled     999          auto   auto 10/100BaseTX

Fa0/4                        disabled     999          auto   auto 10/100BaseTX

Fa0/5     Link to R1         connected    10         a-full  a-100 10/100BaseTX

Fa0/6     Link to PC-A       connected    10         a-full  a-100 10/100BaseTX

Fa0/7                        disabled     999          auto   auto 10/100BaseTX

Fa0/8                        disabled     999          auto   auto 10/100BaseTX

Fa0/9                        disabled     999          auto   auto 10/100BaseTX

Fa0/10                       disabled     999          auto   auto 10/100BaseTX

<output omitted>

S2# show interfaces status

 

Port      Name               Status       Vlan       Duplex  Speed Type

Fa0/1     Link to S1         connected    trunk      a-full  a-100 10/100BaseTX

Fa0/2                        disabled     999          auto   auto 10/100BaseTX

Fa0/3                        disabled     999          auto   auto 10/100BaseTX

<output omitted>

Fa0/14                       disabled     999          auto   auto 10/100BaseTX

Fa0/15                       disabled     999          auto   auto 10/100BaseTX

Fa0/16                       disabled     999          auto   auto 10/100BaseTX

Fa0/17                       disabled     999          auto   auto 10/100BaseTX

Fa0/18    Link to PC-B       connected    10         a-full  a-100 10/100BaseTX

Fa0/19                       disabled     999          auto   auto 10/100BaseTX

Fa0/20                       disabled     999          auto   auto 10/100BaseTX

Fa0/21                       disabled     999          auto   auto 10/100BaseTX

Fa0/22                       disabled     999          auto   auto 10/100BaseTX

Fa0/23                       disabled     999          auto   auto 10/100BaseTX

Fa0/24                       disabled     999          auto   auto 10/100BaseTX

Gi0/1                        disabled     999          auto   auto 10/100/1000BaseTX

Gi0/2                        disabled     999          auto   auto 10/100/1000BaseTX

Step 4:  Document and implement port security features.

The interfaces F0/6 on S1 and F0/18 on S2 are configured as access ports. In this step, you will also configure port security on these two access ports.

  1. On S1, issue the show port-security interface f0/6 command to display the default port security settings for interface F0/6. Record your answers in the table below.

S1# show port-security interface f0/6

Port Security              : Disabled

Port Status                : Secure-down

Violation Mode             : Shutdown

Aging Time                 : 0 mins

Aging Type                 : Absolute

SecureStatic Address Aging : Disabled

Maximum MAC Addresses      : 1

Total MAC Addresses        : 0

Configured MAC Addresses   : 0

Sticky MAC Addresses       : 0

Last Source Address:Vlan   : 0000.0000.0000:0

Security Violation Count   : 0

Default Port Security Configuration

Feature

Default Setting

Port Security

Disabled

Maximum number of MAC addresses

1

Violation Mode

Shutdown

Aging Time

0 mins

Aging Type

Absolute

Secure Static Address Aging

Disabled

Sticky MAC Address

0

  1. On S1, enable port security on F0/6 with the following settings:
  • Maximum number of MAC addresses: 3
  • Violation type: restrict
  • Aging time: 60 min
  • Aging type: inactivity

S1(config)# interface f0/6

S1(config-if)# switchport port-security

S1(config-if)# switchport port-security maximum 3

S1(config-if)# switchport port-security violation restrict

S1(config-if)# switchport port-security aging time 60

S1(config-if)# switchport port-security aging type inactivity

  1. Verify port security on S1 F0/6.

S1# show port-security interface f0/6

Port Security              : Enabled

Port Status                : Secure-up

Violation Mode             : Restrict

Aging Time                 : 60 mins

Aging Type                 : Inactivity

SecureStatic Address Aging : Disabled

Maximum MAC Addresses      : 3

Total MAC Addresses        : 1

Configured MAC Addresses   : 0

Sticky MAC Addresses       : 0

Last Source Address:Vlan   : 0022.5646.3411:10

Security Violation Count   : 0

 

S1# show port-security address

               Secure Mac Address Table

—————————————————————————–

Vlan    Mac Address       Type                          Ports   Remaining Age

                                                                   (mins)

—-    ———–       —-                          —–   ————-

  10    0022.5646.3411    SecureDynamic                 Fa0/6       60 (I)

—————————————————————————–

Total Addresses in System (excluding one mac per port)     : 0

Max Addresses limit in System (excluding one mac per port) : 8192

  1. Enable port security for F0/18 on S2. Configure the port to add MAC addresses learned on the port automatically to the running configuration.

S2(config)# interface f0/18

S2(config-if)# switchport port-security

S2(config-if)# switchport port-security mac-address sticky

  1. Configure the following port security settings on S2 F/18:
  • Maximum number of MAC addresses: 2
  • Violation type: Protect
  • Aging time: 60 min

S2(config)# interface f0/18

S2(config-if)# switchport port-security aging time 60

S2(config-if)# switchport port-security maximum 2

S2(config-if)# switchport port-security violation protect

  1. Verify port security on S2 F0/18.

S2# show port-security interface f0/18

Port Security              : Enabled

Port Status                : Secure-up

Violation Mode             : Protect

Aging Time                 : 60 mins

Aging Type                 : Absolute

SecureStatic Address Aging : Disabled

Maximum MAC Addresses      : 2

Total MAC Addresses        : 1

Configured MAC Addresses   : 0

Sticky MAC Addresses       : 0

Last Source Address:Vlan   : 0022.5646.3413:10

Security Violation Count   : 0

 

S2# show port-security address

               Secure Mac Address Table

—————————————————————————–

Vlan    Mac Address       Type                          Ports   Remaining Age

                                                                   (mins)

—-    ———–       —-                          —–   ————-

  10    0022.5646.3413    SecureSticky                  Fa0/18      

—————————————————————————–

Total Addresses in System (excluding one mac per port)     : 0

Max Addresses limit in System (excluding one mac per port) : 8192

Step 5:  Implement DHCP snooping security.

  1. On S2, enable DHCP snooping and configure DHCP snooping on VLAN 10.

S2(config)# ip dhcp snooping

S2(config)# ip dhcp snooping vlan 10

  1. Configure the trunk port on S2 as a trusted port.

S2(config)# interface f0/1

S2(config-if)# ip dhcp snooping trust

  1. Limit the untrusted port, F18 on S2, to five DHCP packets per second.

S2(config)# interface f0/18

S2(config-if)# ip dhcp snooping limit rate 5

  1. Verify DHCP Snooping on S2.

S2# show ip dhcp snooping

Switch DHCP snooping is enabled

DHCP snooping is configured on following VLANs:

10

DHCP snooping is operational on following VLANs:

10

DHCP snooping is configured on the following L3 Interfaces:

Insertion of option 82 is enabled

   circuit-id default format: vlan-mod-port

   remote-id: 0cd9.96d2.3f80 (MAC)

Option 82 on untrusted port is not allowed

Verification of hwaddr field is enabled

Verification of giaddr field is enabled

DHCP snooping trust/rate is configured on the following Interfaces:

 

Interface                  Trusted    Allow option    Rate limit (pps)

———————    ——-    ————    —————-

FastEthernet0/1            yes        yes             unlimited

  Custom circuit-ids:

FastEthernet0/18           no         no              5

  Custom circuit-ids:

  1. From the command prompt on PC-B, release and then renew the IP address.

C:\Users\Student> ipconfig /release

C:\Users\Student> ipconfig /renew

  1. Verify the DHCP snooping binding using the show ip dhcp snooping binding command.

S2# show ip dhcp snooping binding

MacAddress          IpAddress        Lease(sec)  Type           VLAN  Interface

——————  —————  ———-  ————-  —-  ——————–

00:50:56:90:D0:8E   192.168.10.11    86213       dhcp-snooping   10   FastEthernet0/18

Total number of bindings: 1

Step 6:  Implement PortFast and BPDU guard.

  1. Configure PortFast on all the access ports that are in use on both switches.

S1(config)# interface range f0/5 – 6

S1(config-if)# spanning-tree portfast

S2(config)# interface f0/18

S2(config-if)# spanning-tree portfast

  1. Enable BPDU guard on S1 and S2 VLAN 10 access ports connected to PC-A and PC-B.

S1(config)# interface f0/6

S1(config-if)# spanning-tree bpduguard enable

S2(config)# interface f0/18

S2(config-if)# spanning-tree bpduguard enable

  1. Verify that BPDU guard and PortFast are enabled on the appropriate ports.

S1# show spanning-tree interface f0/6 detail

 Port 8 (FastEthernet0/6) of VLAN0010 is designated forwarding

   Port path cost 19, Port priority 128, Port Identifier 128.6.

   <output omitted for brevity>

   Number of transitions to forwarding state: 1

   The port is in the portfast mode

   Link type is point-to-point by default

   Bpdu guard is enabled

   BPDU: sent 128, received 0

Step 7:  Verify end-to-end connectivity.

Verify PING connectivity between all devices in the IP Addressing Table. If the pings fail, you may need to disable the firewall on the PC hosts.

Close configuration window

Reflection Questions

  1. In reference to Port Security on S2, why is there no timer value for the remaining age in minutes when sticky learning was configured?

Type your answers here.

This switch does not support the port security aging of sticky secure addresses.

  1. In reference to Port Security on S2, if you load the running-config script on S2, why will PC-B on port 18 never get an IP address via DHCP?

Port security is set for only two MAC addresses and port 18 has two “sticky” MAC address bound to the port. Additionally, the violation is protect, which will never send a console/syslog message or increment the violation counter.

  1. In reference to Port Security, what is the difference between the absolute aging type and inactivity aging type?

If the inactivity type is set, then the secure addresses on the port will be removed only if there is no data traffic from the secure source addresses for the specified time period.

If the absolute type is set, then all secure addresses on this port age out exactly after the time specified ends.

End of Document

Device Configurations – Final

Switch S1

S1# show running-config

Building configuration…

 

Current configuration : 5203 bytes

!

version 15.0

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname S1

!

no ip domain-lookup

!

spanning-tree mode pvst

!

vlan 10

 name Management

!

vlan 333

 name Native

!

vlan 999

 name ParkingLot

!

interface FastEthernet0/1

 description Link to S2

 switchport trunk encapsulation dot1q

 switchport trunk native vlan 333

 switchport mode trunk

 switchport nonegotiate

!

interface FastEthernet0/2

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/3

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/4

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/5

 description Link to R1

 switchport access vlan 10

 switchport mode access

 spanning-tree portfast

!

interface FastEthernet0/6

 description Link to PC-A

 switchport access vlan 10

 switchport mode access

 switchport port-security maximum 3

 switchport port-security violation restrict

 switchport port-security aging time 60

 switchport port-security aging type inactivity

 switchport port-security

 spanning-tree portfast

 spanning-tree bpduguard enable

!

interface FastEthernet0/7

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/8

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/9

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/10

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/11

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/12

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/13

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/14

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/15

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/16

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/17

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/18

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/19

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/20

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/21

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/22

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/23

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/24

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface GigabitEthernet0/1

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface GigabitEthernet0/2

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface Vlan1

 no ip address

!

interface Vlan10

 description Management SVI

 ip address 192.168.10.201 255.255.255.0

!

ip default-gateway 192.168.10.1

 

line con 0

 exec-timeout 0 0

 logging synchronous

line vty 0 4

 login

line vty 5 15

 login

!

end

Switch S2

S2# show running-config

Building configuration…

 

Current configuration : 5303 bytes

!

version 15.0

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname S2

!

ip dhcp snooping vlan 10

ip dhcp snooping

no ip domain-lookup

!

spanning-tree mode pvst

!

vlan 10

 name Students

!

vlan 333

 name Native

!

vlan 999

 name ParkingLot

!

interface FastEthernet0/1

 description Link to S1

 switchport trunk native vlan 333

 switchport mode trunk

 switchport nonegotiate

 ip dhcp snooping trust

!

interface FastEthernet0/2

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/3

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/4

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/5

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/6

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/7

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/8

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/9

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/10

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/11

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/12

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/13

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/14

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/15

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/16

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/17

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/18

 description Link to PC-B

 switchport access vlan 10

 switchport mode access

 switchport port-security maximum 2

 switchport port-security violation protect

 switchport port-security mac-address sticky

 switchport port-security aging time 60

 switchport port-security

 spanning-tree portfast

 spanning-tree bpduguard enable

 ip dhcp snooping limit rate 5

!

interface FastEthernet0/19

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/20

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/21

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/22

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/23

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface FastEthernet0/24

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface GigabitEthernet0/1

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface GigabitEthernet0/2

 switchport access vlan 999

 switchport mode access

 shutdown

!

interface Vlan1

 no ip address

!

interface Vlan10

 description Management SVI

 ip address 192.168.10.202 255.255.255.0

!

ip default-gateway 192.168.10.1

!

line con 0

 exec-timeout 0 0

 logging synchronous

line vty 0 4

 login

line vty 5 15

 login

!

end

Leave a comment